在安裝濟南卷簾門之前，廠家一般需要先量好門，因?yàn)椴煌瑘?chǎng)地的尺寸是不一樣的。如果不丈量尺寸，生產出來的門往往無法安裝。那么，在丈量之前，應該注意哪些問題呢？

Before installing Jinan roller shutter door, the manufacturer generally needs to measure the door first, because the size of different sites is different. If the size is not measured, the doors produced often cannot be installed. So, what should we pay attention to before measuring?

1.兩面成直角的墻。丈量師應主動征求客戶意見。結果如下：客戶選擇保持左右線條一致且美觀。丈量師可將目標尺寸縮小120mm，以達到上述目的；二是客戶選擇的目標尺寸不變，安裝人員在墻體兩邊剪直角線，直到合適為止。

1. a wall with two sides at right angles. Surveyors should take the initiative to solicit customers' opinions. The result is as follows: the customer chooses to keep the left and right lines consistent and beautiful. The surveyor can reduce the target size by 120mm to achieve the above purpose; Second, the target size selected by the customer remains unchanged. The installer cuts right angle lines on both sides of the wall until it is appropriate.

2.與墻壁成直角。濟南卷簾門廠家在丈量時要主動詢問客戶對門的意見?？蛻暨x擇保持線條統一美觀。丈量時，可將目標尺寸縮?。s短）60mm，即達到上述目標。其次，客戶選擇的目標尺寸不變，安裝人員可以適時剪線。

2. at right angles to the wall. Jinan roller shutter door manufacturers should take the initiative to ask customers' opinions on the door when measuring. The customer chose to keep the lines uniform and beautiful. When measuring, the target size can be reduced (shortened) by 60mm, that is, to achieve the above goals. Secondly, the target size selected by the customer remains unchanged, and the installer can cut the thread in time.

3.在地板上。由于客戶的實際情況相差較大，一般分為三種：一是地板已經鋪好，可以用丈量法丈量；二是如果不鋪設地板，應降低高度：

3. on the floor. As the actual situation of customers is quite different, it is generally divided into three types: first, the floor has been paved and can be measured by measuring method; Second, if the floor is not laid, the height shall be reduced:

（1）地磚：大理石、瓷磚減薄50mm；

(1) Floor tile: marble and ceramic tile shall be thinned by 50mm;

（2）瓷磚木地板、強化木地板、實木地板減少30mm；

(2) Ceramic tile wood floor, laminate wood floor and solid wood floor shall be reduced by 30mm;

（3）骨架木地板與實際骨架地板的厚度增加10mm。

(3) The thickness of skeleton wood floor and actual skeleton floor shall be increased by 10mm.

（4）左右墻、頂墻的垂直度和傾斜度。丈量師應仔細選擇合適的點作為目標尺寸。

(4) Verticality and inclination of left and right walls and top walls. The surveyor should carefully select the appropriate point as the target size.

（5）安裝人員應主動征求客戶意見。只有當調查人員和客戶表示目標尺寸減少了60毫米時，才實現了保留生產線的愿望。二是客戶選擇的目標尺寸相同（客戶要求門扇大一些），一定要跟客戶說明，小切口要根據直角墻框的邊緣來搭配（效果是線左右不對稱）。

(5) The installer should actively seek the customer's opinions. The desire to retain the production line was realized only when the investigator and the customer stated that the target size had been reduced by 60mm. Second, the target size selected by the customer is the same (the customer requires the door leaf to be larger), so it must be explained to the customer that the small cut should be matched according to the edge of the right angle wall frame (the effect is that the line is asymmetric from left to right).

在卷簾門正式安裝之前，濟南卷簾門廠家要提前派負責人進行丈量，以便生產出尺寸規格更合適的門，方便用戶使用。另外，安裝完成后，檢查門是否可以正常開啟和關閉，以免影響日常使用。更多相關內容就來關注我們網站吧！

Before the formal installation of roller shutter door, the manufacturer of Jinan roller shutter door shall send a person in charge to measure in advance, so as to produce doors with more appropriate dimensions and specifications for the convenience of users. In addition, after installation, check whether the door can be opened and closed normally to avoid affecting daily use. For more information, please visit our website www.jnzxmy Com!