隨著卷簾門在人們生活生產中應用的越來越普及，卷簾的一些問題始終困擾著人們，比如說卷簾門的安裝調試事項，下面濟南卷簾門廠家為您講解一番。

With the increasing popularity of the application of fire shutter doors in people's life and production, some problems of fire shutter have always bothered people, such as the installation and commissioning of the shutter doors. Now, the Jinan shutter door manufacturer will explain to you.

在安裝調試之前應先檢查控制器、按鈕盒、卷門機、行程開關、電剎車的連接線是否正常，確認后在進行調試。

Before installation and commissioning, check whether the connecting lines of the controller, button box, door winder, travel switch and electric brake are normal, and conduct commissioning after confirmation.

1、相序調整：接入三相380V50HZ電源，接通空氣開關，若電源指示燈閃爍故障燈亮故障反饋開關常閉并發出救護笛的報警聲則表明相序錯誤，可將三相電源進線中的任兩相交換即可?？刂破鞯南嘈驒z測正確，操縱按鈕觀察卷簾門運行方向，若卷門機運行方向與按鍵相反，將卷門機三相接線中任意兩相交換即可。

1. Phase sequence adjustment: connect the three-phase 380V50HZ power supply and turn on the air switch. If the power indicator flashes, the fault light turns on, the fault feedback switch is normally closed, and the alarm sound of the ambulance horn comes out, it indicates that the phase sequence is wrong. Exchange any two phases in the three-phase power supply incoming line. The phase sequence detection of the controller is correct, and the operation button is used to observe the operation direction of the roller shutter. If the operation direction of the roller shutter is opposite to the button, exchange any two phases in the three-phase wiring of the roller shutter.

2、中位位置設置以及形成學習：接通電源將控制板上撥嗎開關SW1置于on的位置，SW2置于ON的位置可進入中停位置的設定和正常行駛行程的學習。

2. Middle position setting and formation learning: Turn on the power supply and set the up switch SW1 of the control board to the ON position. Set SW2 to the ON position to enter the middle stop position setting and normal travel learning.

a：現將上下限位器按實際情況設定好。

a: Now set the upper and lower limit stops according to the actual situation.

b：按復位鍵一次卷門機開始上行達到上限位并自動停止。

b: Press the reset key once, the door winder starts to move up to the upper limit and stops automatically.

c：按下行鍵一次開始進入下行全程學習，卷門機開始下行達到下限位并自動停止，下行全程學習完畢。

c: Press the down key once to start the whole downward learning process. The door roller starts to descend to the lower limit and stops automatically. The whole downward learning process is completed.

d：按上行鍵一次開始進入上行全程學習，卷門機開始上行達到上限位并自動停止，上行全程學習完畢。

d: Press the UP key once to start the whole uplink learning. The door roller starts to go up to the upper limit and stops automatically. The whole uplink learning is completed.

e：按上行鍵一次開始進入中停位置學習，卷門機開始下行達到距地面1.8M處按停鍵，下行中位置學習完畢。

e: Press the UP key once to enter the middle stop position for learning. The door winder starts to descend to 1.8m above the ground, and then press the STOP key to finish learning the middle stop position for descending.

f：再按一次下行鍵，使卷門機達到下限位并自動停止，后半程學習完畢。

f: Press the down key again to make the door roller reach the lower limit and stop automatically, and the second half of the learning is completed.

g：按上行鍵，使卷門機達到上限位并自動停止，正常行駛行程學習完畢。

g: Press the up key to make the door roller reach the upper limit and stop automatically, and the learning of normal travel is completed.

h：按消音鍵一次，進入快速下降的中位的學習中位指示燈閃爍表示進入中位設置，按下行鍵，卷門機磁鐵開始間歇下行達到距地面1.8M處按停鍵，快速下降中位置學習完畢。

h: Press the Silence key once, and the learning middle position indicator for entering the fast descending middle position flashes to indicate entering the middle position setting. Press the Down key, and the door roller magnet starts to descend intermittently to the position 1.8M above the ground. Press the Stop key, and the learning of the fast descending middle position is completed.

i：再按復位鍵一次鍵，卷門機達到上限位并自動停止，中停位置于設定和正常行駛行程學習全部完畢。

i: Press the reset key again, the door roller reaches the upper limit and stops automatically, the middle stop is set and the normal travel learning is completed.

本公司就是一家生產銷售各種卷簾門、電動伸縮門，快卷門，防火門等為主的公司。您如果有什么需求或者問題都可以隨時來我們網站http://進行咨詢！

The company is a production and sales of various rolling doors, electric retractable doors, fast rolling doors, fire doors and other companies. If you have any needs or problems, you can come to our website at any time http:// Consult!